FIRE PREVENTION & INDUSTRIAL SAFETY
6 Month Course
Occupation(s) to which the qualification gives access Fire Technology and Industrial Safety Management has a wide scope of Employability ranging from selfemployment, contractual employment to Industrial jobs. On successful completion of this course, the candidates shall be gainfully employed in the industries for following occupations: Fire Fighters Fire Inspector 9 Job description of the occupation Fire Technology and Industrial Safety Management inspects different structures to ensure compliance with central/state government laws and with approved plans, specifications and standards, or inspect fire prevention systems and investigate fire sites to determine cause of fire.
Entry requirements and/or recommendations and minimum age a. Passed class 10th class Examination under 10+2 system of Education or its equivalent. b. The minimum physical requirements are i. Height - 165 cm ii. Weight - 52 kg iii. Chest - Normal 81 cm - Expanded 85 cm iv. A registered MBBS doctor must certify that the candidate is medically fit to undertake the course
Outcomes to be assessed/NOSs to be assesed Assessment criteria for the outcome 1. Apply safe working practices 1.1 Follow and maintain procedures to achieve a safe working environment in line with occupational health and safety regulations and requirements and according to policy. 1.2 Recognize and report all unsafe situations according to policy. 1.3 Identify and take necessary precautions on fire and safety hazards and report according to work policy and procedures. 1.4 Identify, handle and store / dispose-off dangerous goods and substances according to policy and procedures following safety regulations and requirements. 1.5 Identify and observe policies and procedures in regard to illness or accident. 1.6 Identify safety alarms accurately. 1.7 Report supervisor/ Competent of authority in the event of accident or sickness of any staff and record accident details correctly according to accident/injury procedures. 1.8 Identify and observe evacuation procedures according to site policy. 1.9 Identify Personal Productive Equipment (PPE) and use the same as per related working environment. 1.10 Identify basic first aid and use them under different circumstances. 1.11 Identify different fire extinguisher and use the same as per requirement. 2. Comply environment regulation and housekeeping 2.1 Identify environmental pollution & contribute to the avoidance of instances of environmental pollution. 2.2 Deploy environmental protection legislation & regulations. 2.3 Take opportunities to use energy and materials in an environmentally friendly manner. 2.4 Avoid waste and dispose waste as per procedure. 2.5 Recognize different components of 5S and apply the same in the working environment. NSQF QUALIFICATION FILE Fire Technology and Industrial Safety Management 12 3. Interpret & use company and technical communication. 3.1 Obtain sources of information and recognize information. 3.2 Use and draw up technical drawings and documents. 3.3 Use documents and technical regulations and occupationally related provisions. 3.4 Conduct appropriate and target oriented discussions with higher authority and within the team. 3.5 Present facts and circumstances, possible solutions &use English special terminology. 3.6 Resolve disputes within the team 3.7 Conduct written communication. 4. Understand and apply the concept in productivity, quality tools, and labour welfare legislation in day to day work to improve productivity & quality. 4.1Semester examination to test the concept in productivity, quality tools and labour welfare legislation. 4.2 Applications will be assessed during execution of assessable outcome. 5. Explain energy conservation, global warming and pollution and contribute in day to day work by optimally using available resources. 5.1 Semester examination to test knowledge on energy conservation, global warming and pollution. 5.2 Their applications will be assessed during execution of assessable outcome. 6. Explain personnel finance, entrepreneurship and manage/organize related task in day to day work for personal & societal growth. 6.1 Semester examination to test knowledge on personnel finance, entrepreneurship. 6.2 Their applications will be assessed during execution of assessable outcome. 7. Utilize basic computer applications and internet to take benefit of IT developments in the industry. 7.1 Semester examination to test knowledge on basic computer working, basic operating system and uses internet services. 7.2 Their applications will be assessed during execution of assessable outcome.
. Identify and Select suitable chemicals (industrial, inflammable liquid) usable on the workplace. 8.1 Identify various types of acids in the trade. 8.2 Identify the type of acids and their uses in the place. 8.3 Select the suitable acids on the workplace. 8.4 Analyzed the effect of acids on the suitable jobs 9. Identify, select & execute the application of different types of extinguisher, hose & hose fittings. 9.1 Identify of fire and types of extinguishers. 9.2 Install the wall fitting and test it. 9.3 Technique of fire extinction smoothing cooling and Starvation. 9.4 Observe the safety/precaution during the operation Extinguisher. 9.5 identify type of suction and delivery hoses. 9.6 Causes of hose decay & its prevention 9.7 Use of percolating & non-percolating hose 9.8 Identify of hose reel, causes of decay and its care & maintenance. 9.9 Importance of hose reel hose in first aid fire fighting in buildings and industries. 9.10 Plan of work in compliance with standard tests of delivery hoses. 9.11 Standard test of Suction hose 9.12 Identify the different groups of hose fitting. 9.13 Measure of deep lift suction fittings. 9.14 Type of Breechings and its uses. 9.15 Identify the hose ramps, care and maintenance of hose fittings. 10. Select and prepare the hydrant and pump system for proper application. 10.1 Knowledge of Hydrant and Water supplies, 10.2 Identify the hydrant gear and equipment. 10.3 Observe the making of hydrants and testing. 10.4 Prepare the care and maintenance of operation. 10.5 Identify the common type in use. 10.6 Methods of priming. 10.7 Select and testing fault finding. 10.8 Working of centrifugal pump. 10.9 Observe care and maintenance of pump. 11. Plan and execute the working 11.1 Check the hydraulic system NSQF QUALIFICATION FILE Fire Technology and Industrial Safety Management 14 of hydraulics system in work place. 11.2 Check the pressure 11.3 Calculate the water capacity of tank 11.4 Check the working of flow meter 12. Select and categorize electrical hazard and risk & its mitigation. 12.1 Identify common causes of electrical fire 12.2 Select remedial measures 12.3 Identify electrical hazards 12.4 Apply PPE 12.5 Follow the electrical document for safety. 13. Methods of using ladder in practical field. 13.1 Select the appropriate ladder. 13.2 Pitching of ladder. 13.3 Pitching of ladder. 13.4 Climbing the ladder. 13.5 Use leg Lock. 14. Select the BA set and its application in appropriate place. 14.1 Identify and operate B. A. set and relevant drill 14.2 Donning & doffing of SCBA. 14.3 SCBA Operation & Emergency Procedures. 14.4 Inspection and Maintenance of SCBA. 15. Identify and use of small and special gears. 15.1 Identify, select and operate different small and special gears. 15.2 Drill with different small and special gears. 16. Plan and execute elementary treatment at any incidental spot. 16.1 Donning, running and Rescue of casualty through tunnel. 16.2 Apply Sylvester's Method, Holgar Nielsen Method, Rocking Stretcher Method, Emerson Method 16.3 Perform Mouth to Mouth Respiration. 17. Utilization of knots and hitches in different special job and fire. 17.1 Practical use of different knots and hitches in rescue & fire fighting 17.2 Testing of different type of lines. 17.3 Care and maintenance. 18. Plan and execute to up lift various gears with proper techniques. Introduction to Hazard and Risk evaluation & the proper method of rescue & F.F. 18.1 Causes, Identification, Evaluation & Control of hazard and risk. 18.2 Hauling up gears and combined drill NSQF QUALIFICATION FILE Fire Technology and Industrial Safety Management 15 19. Analyze the concept of accident caused and prevention, accident investigation, analysis and safety management. 19.1 Identify different industrial accidents. 19.2 Prepare accident reports. 19.3 Identify Methods Adopted for Reducing Accidents. 19.4 Investigation and analysis of Accidents. 19.5 Safety Slogans, Safety Precautions adopted in the Plant. 19.6 Apply Safety Management, Safety Policy, Safety Committee, , Responsibility of Management, Safety Officers Duties & Responsibilities, Safety Targets, Objectives, Standards, Practices and Performances in work place. 20. Select & apply provisions related to safety, health and welfare in respect of Factory Act, 1948. 20.1 Select & apply provisions related to safety. 20.2 Observation of provisions of the legislation applicable to different factories. 21. Assessment of available resources and their proper use. 21.1 Identify and select various types of Fire Fighting Small and Special rescue gear at Fire Service Station. 21.2 Practical Use of equipments like cutting tools 21.3 Lifting tools Maintenance of tools. 22. Interpret appropriate techniques of CPR. 22.1 Identify techniques of CPR. 22.2 Apply appropriate techniques of CPR. 22.3 Identify and apply Methods for rescue without equipment 23. Identify the importance of lighting, ventilation, work related stress and its measurement. 23.1 Measurement of illumination by Photo meter. 23.2 Measurement of number of air changes in a room 23.3 Measurement of vibration of machine and equipments. SEMESTER-II 24. Plan and execute fixed fire fighting installations for their effective utilization. 24.1 Identify Sprinkler System and their care and maintenance and operational Procedure 24.2 Plan and execute fixed fire fighting installation. 24.3 Utilize fixed fire fighting 24.4 Identify Elementary requirements of Drenchers, Rising Mains, Hose Reels And Down-comer, Fire pump control panel. 24.5 Install Fixed Foam. NSQF QUALIFICATION FILE Fire Technology and Industrial Safety Management 16 25. Select and use PPE, its care and maintenance. 25.1 Identify various Personal Protective Equipments. 25.2 Select and use Respiratory and Non-respiratory Personal Protective Equipment, their Care & Maintenance. 25.3 Observe standard and regulation related to PPE. 26. Select Automatic Fire Detection cum Alarm System to plan their effective utilization. 26.1 Identify various types of detectors. 26.2 Select Automatic Fire Detection cum Alarm System as per need. 26.3 Plan Automatic Fire Detection cum Alarm Systems effective utilization. 27. Plan and execute fire station administration. 27.1 Identify various important duties of a fire station. 27.2 Drill with ladder and water tender 27.3 Foam Drill with FBI0X single delivery. 27.4 Foam Drill with FB5X single delivery. 27.5 Wet Drill with double delivery. 27.6 Dry Drill with double delivery. 28. Identify communication system in different organization and their scope of use. 28.1 Identify different communication required at various fire service departments. 28.2 Identify, select and apply Various lines, communication Equipment in Fire Service. 28.3 Select & use Method of receiving report of emergencies. 28.4 Identify and use Radio Communication and VHF. 28.5 Practices Writing of Occurrence Book, Duty Card/ Register, Log Book, Hose Book, Stock Register and their maintenance. 28.6 Apply fire affected room searching techniques. 29. Accustomed with different fire situations and fire fighting using extinguishers. 29.1 Perform live fire extinction using all kind of extinguisher. 29.2 Identify Fire Hazards in rural areas and cause of fire. 29.3 Identify, select and apply Method of Fire-fighting in rural areas. 29.4 Identify Difficulties in dealing with Rural fires. 30. Plan and execute disaster response practices, IRS/JRT and salvage technique. 30.1 Identify Natural and Man-made Disaster. 30.2 Use various agencies, first responders, control of situation. 30.3 Identify different types of disasters. 30.4 Simulated Practices to control life and properties damages from natural disaster. 30.5 Perform Water relay drill (All types). NSQF QUALIFICATION FILE Fire Technology and Industrial Safety Management 17 30.6 Identify and select Equipment for Salvage & working at Fires 30.7 Use salvage sheets & equipments and there care & maintenance. 30.8 Identify, select and apply Methods of entry into building. 30.9 Identify, select and apply Different searching methods to locate & rescue a trapped causality. 31. Select and apply correct rescue method. 31.1 Observe safety Precautions when working in smoke laden buildings. 31.2 Identify, select and apply various Emergency methods of rescue. 31.3 Identify hazards associated with various rescue operations. 31.4 Select & apply various rescue equipments. 32. Categorize building construction that can ensure fire and life safety. 32.1 Familiarization at construction site. 32.2 Identify building materials. 32.3 Plan escapes routine. 32.4 Practical training about Care and maintenance of sprinklers. 32.5 Use of Automatic fire alarm system, fire exit drill 33. Plan and execute fire protection measures based on construction and occupancy. 33.1 Classification of building in the country 33.2 Identify Building materials and their behavior under fire conditions 33.3 Identify and apply various types of occupancies and fire fighting techniques. 33.4 Identify Important fire escapes with respect to there positioning. 34. Plan and survey Airport & Aircraft, port and ship for rescue system and fire fighting system on it. 34.1 Identify Different types of Air-crafts, Air craft fire fighting and rescue procedures. 34.2 Identify types of emergencies and apply method of dealing with each emergency. 34.3 Recognize ship fire protection and fire fighting & rescue from ship. 35. Identify occupational hazards associated with different dangerous chemicals, dust, gases, mist, vapours etc. to 35.1 Identify HVAC system. 35.2 Identify various equipments used in rescue of causality. 35.3 Ladder Drill with Fireman Lift. 35.4 Sewer Rescue drill. NSQF QUALIFICATION FILE Fire Technology and Industrial Safety Management 18 plan and execute rescue operations in these cases. 35.5 Stretcher drill. 35.6 Identify Occupational Hazards & Dangerous Chemicals. 35.7 Identify Dangerous Properties of Chemicals, Dust, Gases, Fumes, Mist, Vapours, Smoke and Aerosols. 36. Observed safety precautions while working at height, confined place and work permit system. 36.1 Perform High elevation drill. 36.2 Perform Confined space rescue. 36.3 Observe safety precaution related to Scaffolds, Ladders, and Work at height including Roof Work. 37. Identify the characteristics of various fire suppression agents including water. Understand safety in manual and mechanical handling of materials. 37.1 Identify the characteristics of various fire suppression agents including water. 37.2 Perform Mechanical and Manual Material Handling. 37.3 Observe Safety related to Mechanical and Manual Material Handling, Lifting Appliances, Transport / Earthmoving& Material Handling Equipments. 38. Analysis hazard evaluation and risk analysis exercise. 38.1 Perform exercise on Hazard evaluation and risk. 38.2 Use safety belt, helmets, gloves and goggles. 38.3 Identify Transportation and handling of dangerous chemicals and explosives.